What's the PSR?
Moderators: OutBack Moderator Team, OutBack
-
ericwahl
- Forum Guru
- Posts: 132
- Joined: Wed Mar 13, 2002 11:01 pm
- My RE system: (9) SW230mono, XW-60-MPPT, SW5548
- Contact:
What's the PSR?
Hi-
When you get back from the fair,
In the photo of the PSR-FO with the 8 red batteries, are those T-105 or L-16?
http://www.outbackpower.com/psr.htm
I can't help thinking the rack looks a little tall for one level of L-16, and a little short for 2 levels. How about one box for 8 or 16 L-16/S530 ?
Or is 8D the way to go now? I'm so behind the times.
With bottom, side, and top insulation of course.
Thanks,
Eric
When you get back from the fair,
In the photo of the PSR-FO with the 8 red batteries, are those T-105 or L-16?
http://www.outbackpower.com/psr.htm
I can't help thinking the rack looks a little tall for one level of L-16, and a little short for 2 levels. How about one box for 8 or 16 L-16/S530 ?
Or is 8D the way to go now? I'm so behind the times.
With bottom, side, and top insulation of course.
Thanks,
Eric
-
Christopher
What's the PSR?
The PSR was originally designed to house smaller batteries - not the L16s. The only version that handles them well is the "frame only" version PSR-FO. Some installer are using the PSR-FO and then making a plywood cover that is removeable for servicing. Since you can put the L16s on two levels, they take up less floor space.
The PSR is designed to allow for the addition of insulation by the installer. Standard 1" thick styrofoam fits very nicely and is easy to get. The outdoor kit for the PSR includes an insulated top to prevent condensation from dripping onto the electronics/batteries inside.
I do not advocate using the 8D batteries usually. Concorde offers the Group 31 batteries in both 6 and 12 vdc with a 105 AH rating. If you do not want to use sealed batteries, then I usually suggest a golf cart battery as they are the best bang for the buck. On larger systems (more than 16 batteries) I would go to L16s or larger 2 volt type batteries.
BTW - the PSR will fit up to EIGHT of the new FX2000 inverters with only one additional shelf kit required (and no mounting plate needed). Look for some pictures on the web soon of this and other configurations.
<small>[ June 30, 2002, 06:33 PM: Message edited by: Christopher Freitas ]</small>
The PSR is designed to allow for the addition of insulation by the installer. Standard 1" thick styrofoam fits very nicely and is easy to get. The outdoor kit for the PSR includes an insulated top to prevent condensation from dripping onto the electronics/batteries inside.
I do not advocate using the 8D batteries usually. Concorde offers the Group 31 batteries in both 6 and 12 vdc with a 105 AH rating. If you do not want to use sealed batteries, then I usually suggest a golf cart battery as they are the best bang for the buck. On larger systems (more than 16 batteries) I would go to L16s or larger 2 volt type batteries.
BTW - the PSR will fit up to EIGHT of the new FX2000 inverters with only one additional shelf kit required (and no mounting plate needed). Look for some pictures on the web soon of this and other configurations.
<small>[ June 30, 2002, 06:33 PM: Message edited by: Christopher Freitas ]</small>
-
Dave Palumbo
- Forum Member
- Posts: 16
- Joined: Sun May 12, 2002 11:01 pm
- Location: Hyde Park, Vermont
- Contact:
What's the PSR?
Christopher,
I do not see any pictures on your site yet of the FX2024 used with your PSR?
I would like to know how this rack is working out for your dealers?
I am designing a small system for an island cottage in Trinidad. With 4 Concorde PVX 1040T AGM batteries. Is there enough room for 1 FX2024 inverter and a C40 controller on a PSR-MP inside the enclosure? It looks like the 175A breaker and the two 40A pv array breakers would be directly in front of the FX.
Is the spill containment tray agood idea even for AGM batteries?
What PSR options would I want with this system?
Best,
Dave Palumbo
I do not see any pictures on your site yet of the FX2024 used with your PSR?
I would like to know how this rack is working out for your dealers?
I am designing a small system for an island cottage in Trinidad. With 4 Concorde PVX 1040T AGM batteries. Is there enough room for 1 FX2024 inverter and a C40 controller on a PSR-MP inside the enclosure? It looks like the 175A breaker and the two 40A pv array breakers would be directly in front of the FX.
Is the spill containment tray agood idea even for AGM batteries?
What PSR options would I want with this system?
Best,
Dave Palumbo
-
Christopher
What's the PSR?
David - Yes the PSR works great with the FX inverter. We have taken the photos but are working on our next catalog and haven't added them to the website yet.
The PSR-MP (PSR mounting plate) allows mounting of a FX and a MX60 controller (or C40 - same mounting holes and knockout locations - funny how that is...). There is also room for up to 4 of the Concorde 100 amphour 12V batteries in the lower part of the enclosure still. If you add another shelf you can even have 8 of the group 31 batteries with the inverter/controller.
The bracket on the front holds up to five of the small DC breakers and one of the large breakers (100/175/250).
The spill containment tray is not required with sealed batteries - but there are some UBC type standards that may require them with sealed batteries.
The only other option for this would be a siesmic mounting kit if required - it also allows you to mount the PSR down to the ground permanently.
Hope this helps.
Christopher
</font><blockquote><font size="1" face="Verdana, Helvetica, sans-serif">quote:</font><hr /><font size="2" face="Verdana, Helvetica, sans-serif">Originally posted by Dave Palumbo:
<strong>Christopher,
I do not see any pictures on your site yet of the FX2024 used with your PSR?
I would like to know how this rack is working out for your dealers?
I am designing a small system for an island cottage in Trinidad. With 4 Concorde PVX 1040T AGM batteries. Is there enough room for 1 FX2024 inverter and a C40 controller on a PSR-MP inside the enclosure? It looks like the 175A breaker and the two 40A pv array breakers would be directly in front of the FX.
Is the spill containment tray agood idea even for AGM batteries?
What PSR options would I want with this system?
Best,
Dave Palumbo</strong></font><hr /></blockquote><font size="2" face="Verdana, Helvetica, sans-serif">
The PSR-MP (PSR mounting plate) allows mounting of a FX and a MX60 controller (or C40 - same mounting holes and knockout locations - funny how that is...). There is also room for up to 4 of the Concorde 100 amphour 12V batteries in the lower part of the enclosure still. If you add another shelf you can even have 8 of the group 31 batteries with the inverter/controller.
The bracket on the front holds up to five of the small DC breakers and one of the large breakers (100/175/250).
The spill containment tray is not required with sealed batteries - but there are some UBC type standards that may require them with sealed batteries.
The only other option for this would be a siesmic mounting kit if required - it also allows you to mount the PSR down to the ground permanently.
Hope this helps.
Christopher
</font><blockquote><font size="1" face="Verdana, Helvetica, sans-serif">quote:</font><hr /><font size="2" face="Verdana, Helvetica, sans-serif">Originally posted by Dave Palumbo:
<strong>Christopher,
I do not see any pictures on your site yet of the FX2024 used with your PSR?
I would like to know how this rack is working out for your dealers?
I am designing a small system for an island cottage in Trinidad. With 4 Concorde PVX 1040T AGM batteries. Is there enough room for 1 FX2024 inverter and a C40 controller on a PSR-MP inside the enclosure? It looks like the 175A breaker and the two 40A pv array breakers would be directly in front of the FX.
Is the spill containment tray agood idea even for AGM batteries?
What PSR options would I want with this system?
Best,
Dave Palumbo</strong></font><hr /></blockquote><font size="2" face="Verdana, Helvetica, sans-serif">
-
sunwind
What's the PSR?
Hi Christopher,
I'm working on a small cottage system where mounting the FX, controller & batteries in a PSR seems like a great option. I'd like to send my customer a pic of such an installation, like the partial photo in the catalog. The website only has examples using an SW. Can you please have the new pic(s) posted, or send via email?
Thanks,
-Kelly
[QUOTE]Originally posted by Christopher Freitas:
[QB]David - Yes the PSR works great with the FX inverter. We have taken the photos but are working on our next catalog and haven't added them to the website yet.
I'm working on a small cottage system where mounting the FX, controller & batteries in a PSR seems like a great option. I'd like to send my customer a pic of such an installation, like the partial photo in the catalog. The website only has examples using an SW. Can you please have the new pic(s) posted, or send via email?
Thanks,
-Kelly
[QUOTE]Originally posted by Christopher Freitas:
[QB]David - Yes the PSR works great with the FX inverter. We have taken the photos but are working on our next catalog and haven't added them to the website yet.
-
ericwahl
- Forum Guru
- Posts: 132
- Joined: Wed Mar 13, 2002 11:01 pm
- My RE system: (9) SW230mono, XW-60-MPPT, SW5548
- Contact:
What's the PSR?
I just built one w/ 8 batts and a DR. Fit perfectly. With 4 batts you'd have lots of room.
Went together very nicely.
I only took one photo:
http://www.solarblog.com/datas/users/1-psr-1.jpg
[img]images/smiles/icon_smile.gif[/img]
Went together very nicely.
I only took one photo:
http://www.solarblog.com/datas/users/1-psr-1.jpg
[img]images/smiles/icon_smile.gif[/img]
-
boB
What's the PSR?
Here's a picture of an outdoor PSR installation that was sent to Christopher... Until we have our own spot to post pix of installations, I'll just put it up on my personal web site for now...
Let me know if you would like a higher res picture than this scaled down one.
boB
http://www.eskimo.com/~bgudgel/PSR_outdoors.jpg
<small>[ November 01, 2003, 01:50 PM: Message edited by: boB Gudgel ]</small>
Let me know if you would like a higher res picture than this scaled down one.
boB
http://www.eskimo.com/~bgudgel/PSR_outdoors.jpg
<small>[ November 01, 2003, 01:50 PM: Message edited by: boB Gudgel ]</small>
- shastatodd
- Forum Guru
- Posts: 260
- Joined: Thu Oct 17, 2002 11:01 pm
- My RE system: SYSTEM ONE:
A single, turbocharged GVFX-3648 inverter S/N 101 (includes DT kludge & MX60 for generator charging); 5 kW STC of actively tracked PV; turbocharged FM80 charge controller; Legacy Hub 4; eight, 2008 vintage Surrette FC-420 flooded lead calcium batteries; E-Meter (Link-10); Mate3s.
SYSTEM TWO:
A single, sealed GTFX-2524 inverter; 2.0 kW STC of actively tracked PV; turbocharged FM60 charge controller; four, 2017 vintage Surrette FC-420 flooded lead calcium batteries; E-Meter (Link-10).
The 7kW PV, 2 inverter system typically sells an average of 20 kWh/day.
Peak summer production is 50 kWh/day.
The original, April of 1999, Home Power guerilla solar system #2 was legally permitted in April of 2005, with grandfathered yearly net metering through PP&L.
I also have a 2 @ 4' X 10' flat plate, glycol based SHW system which provides 85% of our yearly hot water needs.
Our home is zero energy which includes winter heating, hot water & charging of our 2013 Chevy Volt. - Location: Mt. Shasta, CA.
- Contact:
What's the PSR?
Is it possible to buy just the green plastic anti-spill pans that you use in the battery holder? I am putting my batteries on the floor and just need spill containment. If you cannot sell these can you direct me to who makes these for you so I might inquire directly with them?
Thanks,
Todd
Thanks,
Todd
-
Scott Payne
What's the PSR?
Those pans have an OutBack part number of PSR-SCT (for spill containment tray). They our on our price list for $29 apiece.
Any of our distributors should have these in stock.
Scott
Any of our distributors should have these in stock.
Scott