What is the status of Outback Power

General Talk

Moderators: OutBack Moderator Team, OutBack

solar-er
Forum Member
Posts: 6
Joined: Tue Feb 23, 2010 9:57 am
My RE system: Solec S-050 x2, Arco M52 x8, Bobier M-8, Sunselector M-4, Powerstar 600 (upgraded to 800),
Statpower 1000, Todd TS30, Trace T240, Whisper 600, Air 403, Trojan 24Ts and this and that

Re: What is the status of Outback Power

Post by solar-er » Mon May 05, 2025 8:08 am

sadly, only change is permanent.
some of you (geeks & installers) have been around a long time. Hats off to you.
companies come and go. Some new, some reborn. Trace> "original" Outback before Alpha, Midnite, Xantrex after Schneider.
Distributors/Resellers also, "original" Alternative Energy Engr>, Applied Power Corp, DCPower
such a long list.
While subsequent new companies have been (arguably) successful after the divorce,
I have yet to see a long term successful merger/acquisition. Customer service seems to always be first to go.
Some installers have (many) dozens of systems and want to support their customers.
Maybe it's time to tell them to update.
Afterall, Chrysler is now Stellantis

bigjimchest
Forum Whiz
Posts: 39
Joined: Mon Jan 24, 2022 4:37 am
My RE system: OutBack Inverter 50A GS8048A, Q CELLS 430W Solar Panel 144 cells Q.Peak (18)

Re: What is the status of Outback Power

Post by bigjimchest » Fri Mar 27, 2026 4:31 am

I was curious what the status is of outback. I ended up finaly upgrading to the Sol-Ark 15kw system and I must say after working out some kinks with its equivalent Grid Zero feature, been running solid for 8 months. Problably put the 3 flexmax 80 and GS 8048 inverter up on EBay. I do understand that it is High Frequency inverter, but I definately have not had any problems with my welder or charging my EV. another nice feature is the higher input voltages on the charge controllers, makes it much easier to run wires for ground based systems. I still see that everthing still is out of stock, even the FM100 I tried to buy when I was considering upgrading and adding another inverter...very sad.

chrisski
Forum Czar
Posts: 537
Joined: Fri May 17, 2024 7:23 pm
My RE system: Dual 8048 Radian w/ Load Center
Mate 3
Flex max 100 afci X 4
Fortress eFlex 5.1 kWh Battery X 8
TP1000 for Internet Connectivity
Location: Central AZ, lowland desert

Re: What is the status of Outback Power

Post by chrisski » Fri Mar 27, 2026 2:36 pm

If Sol Arl has a 15 kW grid zero feature that is nice.

My max “brief” output for a few minutes is around 12 kW. Too much for Outbacks limiting grid zero to a single 8 kW radian.

raysun
Forum Overlord
Posts: 13673
Joined: Tue Jul 26, 2016 5:57 am
My RE system: (Former system. Now retired.)
Flexpower Two: (2) FXR3048A-01 - Series Stacked, (2) FM80, MATE3s, FlexNetDC
6 SimpliPhi 3.8-48 (48v @ 75AH. 450AH total)
Outback IBR3 battery enclosure
REC Alpha 440W panels - 2 arrays: each of 4 strings of 2 in series
2 Midnite Solar MNPV6 combiners w/20A DC disconnects.
Honda EU7000is gas fuel generator
Off-Grid

Re: What is the status of Outback Power

Post by raysun » Sat Mar 28, 2026 12:23 pm

chrisski wrote: ↑
Fri Mar 27, 2026 2:36 pm
If Sol Arl has a 15 kW grid zero feature that is nice.

My max “brief” output for a few minutes is around 12 kW. Too much for Outbacks limiting grid zero to a single 8 kW radian.
Outback has done an admirable job shoe-horning evolved functionality into a 20 year-old architecture. It is, however, increasingly long in the tooth and struggling to keep pace.
The GS and FX inverters have a solid foundation, and if the use case fits their capabilities, they will serve reliably for a long time to come.
However, for many folks that use case is shifting.

bigjimchest
Forum Whiz
Posts: 39
Joined: Mon Jan 24, 2022 4:37 am
My RE system: OutBack Inverter 50A GS8048A, Q CELLS 430W Solar Panel 144 cells Q.Peak (18)

Re: What is the status of Outback Power

Post by bigjimchest » Sat Mar 28, 2026 2:33 pm

chrisski wrote: ↑
Fri Mar 27, 2026 2:36 pm
If Sol Arl has a 15 kW grid zero feature that is nice.

My max “brief” output for a few minutes is around 12 kW. Too much for Outbacks limiting grid zero to a single 8 kW radian.
They do have a zero export plus CT Sensors on the Mains to make sure if you backfeed the 30 amp breaker in the main panel it will adjust the amount to keep a constant 200W Draw and buffer.

bigjimchest
Forum Whiz
Posts: 39
Joined: Mon Jan 24, 2022 4:37 am
My RE system: OutBack Inverter 50A GS8048A, Q CELLS 430W Solar Panel 144 cells Q.Peak (18)

Re: What is the status of Outback Power

Post by bigjimchest » Sat Mar 28, 2026 2:40 pm

raysun wrote: ↑
Sat Mar 28, 2026 12:23 pm
chrisski wrote: ↑
Fri Mar 27, 2026 2:36 pm
If Sol Arl has a 15 kW grid zero feature that is nice.

My max “brief” output for a few minutes is around 12 kW. Too much for Outbacks limiting grid zero to a single 8 kW radian.
Outback has done an admirable job shoe-horning evolved functionality into a 20 year-old architecture. It is, however, increasingly long in the tooth and struggling to keep pace.
The GS and FX inverters have a solid foundation, and if the use case fits their capabilities, they will serve reliably for a long time to come.
However, for many folks that use case is shifting.
Hi Raysun, good to see your still around the forum. I agree that the Low frequency inverter was build like a battleship and pretty bullet proof.. but when the time came to upgrade or buy spares, they just could not ship product. I looked around and still everything is out of stock. I was just curious if they ever got there act together. Also as a side note as I think about it, I have been finding alot of bad battery balancers for My 12.8V LiFePO4 batteries. tried 4 different brands and the only ones that are any good are by MAZAva. my favorites so far are the PLC-10 that mount on a Din Rail.
EndOf Day.jpg

raysun
Forum Overlord
Posts: 13673
Joined: Tue Jul 26, 2016 5:57 am
My RE system: (Former system. Now retired.)
Flexpower Two: (2) FXR3048A-01 - Series Stacked, (2) FM80, MATE3s, FlexNetDC
6 SimpliPhi 3.8-48 (48v @ 75AH. 450AH total)
Outback IBR3 battery enclosure
REC Alpha 440W panels - 2 arrays: each of 4 strings of 2 in series
2 Midnite Solar MNPV6 combiners w/20A DC disconnects.
Honda EU7000is gas fuel generator
Off-Grid

Re: What is the status of Outback Power

Post by raysun » Sat Mar 28, 2026 3:01 pm

I've been trying to find replacement parts for FX/FXR inverters, but no joy. I have pretty much given up on relying on those.

Series connected 12V LFP can be a bit touchy to keep in balance. I've had better results building (or installing) batteries of the "native' system voltage, e.g. 48V.

User avatar
shastatodd
Forum Guru
Posts: 260
Joined: Thu Oct 17, 2002 11:01 pm
My RE system: SYSTEM ONE:
A single, turbocharged GVFX-3648 inverter S/N 101 (includes DT kludge & MX60 for generator charging); 5 kW STC of actively tracked PV; turbocharged FM80 charge controller; Legacy Hub 4; eight, 2008 vintage Surrette FC-420 flooded lead calcium batteries; E-Meter (Link-10); Mate3s.

SYSTEM TWO:
A single, sealed GTFX-2524 inverter; 2.0 kW STC of actively tracked PV; turbocharged FM60 charge controller; four, 2017 vintage Surrette FC-420 flooded lead calcium batteries; E-Meter (Link-10).

The 7kW PV, 2 inverter system typically sells an average of 20 kWh/day.
Peak summer production is 50 kWh/day.

The original, April of 1999, Home Power guerilla solar system #2 was legally permitted in April of 2005, with grandfathered yearly net metering through PP&L.

I also have a 2 @ 4' X 10' flat plate, glycol based SHW system which provides 85% of our yearly hot water needs.

Our home is zero energy which includes winter heating, hot water & charging of our 2013 Chevy Volt.
Location: Mt. Shasta, CA.
Contact:

Re: What is the status of Outback Power

Post by shastatodd » Sun Mar 29, 2026 2:51 am

raysun wrote: ↑
Sat Mar 28, 2026 3:01 pm
I've been trying to find replacement parts for FX/FXR inverters, but no joy. I have pretty much given up on relying on those.
So replacement boards for FX inverters are no longer available? Yikes, I guess I should have bought more spares.

raysun
Forum Overlord
Posts: 13673
Joined: Tue Jul 26, 2016 5:57 am
My RE system: (Former system. Now retired.)
Flexpower Two: (2) FXR3048A-01 - Series Stacked, (2) FM80, MATE3s, FlexNetDC
6 SimpliPhi 3.8-48 (48v @ 75AH. 450AH total)
Outback IBR3 battery enclosure
REC Alpha 440W panels - 2 arrays: each of 4 strings of 2 in series
2 Midnite Solar MNPV6 combiners w/20A DC disconnects.
Honda EU7000is gas fuel generator
Off-Grid

Re: What is the status of Outback Power

Post by raysun » Sun Mar 29, 2026 8:38 am

shastatodd wrote: ↑
Sun Mar 29, 2026 2:51 am
raysun wrote: ↑
Sat Mar 28, 2026 3:01 pm
I've been trying to find replacement parts for FX/FXR inverters, but no joy. I have pretty much given up on relying on those.
So replacement boards for FX inverters are no longer available? Yikes, I guess I should have bought more spares.
I don't know if they are discontinued or if its an availability issue. I couldn't find an FXR control board however

User avatar
shastatodd
Forum Guru
Posts: 260
Joined: Thu Oct 17, 2002 11:01 pm
My RE system: SYSTEM ONE:
A single, turbocharged GVFX-3648 inverter S/N 101 (includes DT kludge & MX60 for generator charging); 5 kW STC of actively tracked PV; turbocharged FM80 charge controller; Legacy Hub 4; eight, 2008 vintage Surrette FC-420 flooded lead calcium batteries; E-Meter (Link-10); Mate3s.

SYSTEM TWO:
A single, sealed GTFX-2524 inverter; 2.0 kW STC of actively tracked PV; turbocharged FM60 charge controller; four, 2017 vintage Surrette FC-420 flooded lead calcium batteries; E-Meter (Link-10).

The 7kW PV, 2 inverter system typically sells an average of 20 kWh/day.
Peak summer production is 50 kWh/day.

The original, April of 1999, Home Power guerilla solar system #2 was legally permitted in April of 2005, with grandfathered yearly net metering through PP&L.

I also have a 2 @ 4' X 10' flat plate, glycol based SHW system which provides 85% of our yearly hot water needs.

Our home is zero energy which includes winter heating, hot water & charging of our 2013 Chevy Volt.
Location: Mt. Shasta, CA.
Contact:

Re: What is the status of Outback Power

Post by shastatodd » Sun Mar 29, 2026 9:21 am

And the FXR is the newer model so that's not good.

I honestly can't see why anyone would ever specify Outback gear for new installations.

raysun
Forum Overlord
Posts: 13673
Joined: Tue Jul 26, 2016 5:57 am
My RE system: (Former system. Now retired.)
Flexpower Two: (2) FXR3048A-01 - Series Stacked, (2) FM80, MATE3s, FlexNetDC
6 SimpliPhi 3.8-48 (48v @ 75AH. 450AH total)
Outback IBR3 battery enclosure
REC Alpha 440W panels - 2 arrays: each of 4 strings of 2 in series
2 Midnite Solar MNPV6 combiners w/20A DC disconnects.
Honda EU7000is gas fuel generator
Off-Grid

Re: What is the status of Outback Power

Post by raysun » Sun Mar 29, 2026 9:46 am

shastatodd wrote: ↑
Sun Mar 29, 2026 9:21 am
And the FXR is the newer model so that's not good.

I honestly can't see why anyone would ever specify Outback gear for new installations.
Sadly, after being an advocate for over a decade, I no longer suggest it. The legacy products seem to be orphaned, the new products are an unknown, but inevitably will be Outback badged kit in a very crowded field of "next generation" look-alike products.

A neighbor has two 24V outback systems in his off grid home. The recent storm that dropped 20" of rain in 24 hours killed both his Chinese no-name 24V LFP batteries (poor weather protection on his part). His supplier swapped the dead units for 48V batteries so now he needs to upgrade inverters. 48V FX class would be drop-in replacements (for about $4k), but aren't readily available.
I suggested he combine the two systems and deploy a single inverter. We settled on a nice blue colored one from a different vendor.

User avatar
shastatodd
Forum Guru
Posts: 260
Joined: Thu Oct 17, 2002 11:01 pm
My RE system: SYSTEM ONE:
A single, turbocharged GVFX-3648 inverter S/N 101 (includes DT kludge & MX60 for generator charging); 5 kW STC of actively tracked PV; turbocharged FM80 charge controller; Legacy Hub 4; eight, 2008 vintage Surrette FC-420 flooded lead calcium batteries; E-Meter (Link-10); Mate3s.

SYSTEM TWO:
A single, sealed GTFX-2524 inverter; 2.0 kW STC of actively tracked PV; turbocharged FM60 charge controller; four, 2017 vintage Surrette FC-420 flooded lead calcium batteries; E-Meter (Link-10).

The 7kW PV, 2 inverter system typically sells an average of 20 kWh/day.
Peak summer production is 50 kWh/day.

The original, April of 1999, Home Power guerilla solar system #2 was legally permitted in April of 2005, with grandfathered yearly net metering through PP&L.

I also have a 2 @ 4' X 10' flat plate, glycol based SHW system which provides 85% of our yearly hot water needs.

Our home is zero energy which includes winter heating, hot water & charging of our 2013 Chevy Volt.
Location: Mt. Shasta, CA.
Contact:

Re: What is the status of Outback Power

Post by shastatodd » Sun Mar 29, 2026 11:46 am

Yes it seems like victron is filling the gap for many people.

One of the beauties of Outback gear is field replaceable circuit boards but if there's no replacements available, then that beauty is gone.

It's really sad to watch a company shoot themselves in the foot... And at 70 years old now, I'm loathe to rebuild my entire system... so I will try to source more replacement boards to keep things operational until I'm no longer around to worry about it.

raysun
Forum Overlord
Posts: 13673
Joined: Tue Jul 26, 2016 5:57 am
My RE system: (Former system. Now retired.)
Flexpower Two: (2) FXR3048A-01 - Series Stacked, (2) FM80, MATE3s, FlexNetDC
6 SimpliPhi 3.8-48 (48v @ 75AH. 450AH total)
Outback IBR3 battery enclosure
REC Alpha 440W panels - 2 arrays: each of 4 strings of 2 in series
2 Midnite Solar MNPV6 combiners w/20A DC disconnects.
Honda EU7000is gas fuel generator
Off-Grid

Re: What is the status of Outback Power

Post by raysun » Sun Mar 29, 2026 12:16 pm

Yes, it's an odd situation these days to have equipment outlast the company that designed it, but such is the modern world.

User avatar
shastatodd
Forum Guru
Posts: 260
Joined: Thu Oct 17, 2002 11:01 pm
My RE system: SYSTEM ONE:
A single, turbocharged GVFX-3648 inverter S/N 101 (includes DT kludge & MX60 for generator charging); 5 kW STC of actively tracked PV; turbocharged FM80 charge controller; Legacy Hub 4; eight, 2008 vintage Surrette FC-420 flooded lead calcium batteries; E-Meter (Link-10); Mate3s.

SYSTEM TWO:
A single, sealed GTFX-2524 inverter; 2.0 kW STC of actively tracked PV; turbocharged FM60 charge controller; four, 2017 vintage Surrette FC-420 flooded lead calcium batteries; E-Meter (Link-10).

The 7kW PV, 2 inverter system typically sells an average of 20 kWh/day.
Peak summer production is 50 kWh/day.

The original, April of 1999, Home Power guerilla solar system #2 was legally permitted in April of 2005, with grandfathered yearly net metering through PP&L.

I also have a 2 @ 4' X 10' flat plate, glycol based SHW system which provides 85% of our yearly hot water needs.

Our home is zero energy which includes winter heating, hot water & charging of our 2013 Chevy Volt.
Location: Mt. Shasta, CA.
Contact:

Re: What is the status of Outback Power

Post by shastatodd » Sun Mar 29, 2026 12:26 pm

I totally agree and it's also a testimony to the nerds at Outback who built stuff back when things like longevity mattered.
Last edited by shastatodd on Mon Mar 30, 2026 12:45 am, edited 1 time in total.

raysun
Forum Overlord
Posts: 13673
Joined: Tue Jul 26, 2016 5:57 am
My RE system: (Former system. Now retired.)
Flexpower Two: (2) FXR3048A-01 - Series Stacked, (2) FM80, MATE3s, FlexNetDC
6 SimpliPhi 3.8-48 (48v @ 75AH. 450AH total)
Outback IBR3 battery enclosure
REC Alpha 440W panels - 2 arrays: each of 4 strings of 2 in series
2 Midnite Solar MNPV6 combiners w/20A DC disconnects.
Honda EU7000is gas fuel generator
Off-Grid

Re: What is the status of Outback Power

Post by raysun » Mon Mar 30, 2026 12:06 am

I was talking to my Canadian cousin last week, and he mentioned that an FX inverter (one of five) that we installed in 2005 was still working!
The other 4 may be as well, but were confiscated by the authorities from greenhouses in Penticton in 2010. Apparently growing hydroponic tomatoes was against the law in B.C. At least the grower said they were tomatoes. Kinda funny looking, but that's Canada for you.

User avatar
shastatodd
Forum Guru
Posts: 260
Joined: Thu Oct 17, 2002 11:01 pm
My RE system: SYSTEM ONE:
A single, turbocharged GVFX-3648 inverter S/N 101 (includes DT kludge & MX60 for generator charging); 5 kW STC of actively tracked PV; turbocharged FM80 charge controller; Legacy Hub 4; eight, 2008 vintage Surrette FC-420 flooded lead calcium batteries; E-Meter (Link-10); Mate3s.

SYSTEM TWO:
A single, sealed GTFX-2524 inverter; 2.0 kW STC of actively tracked PV; turbocharged FM60 charge controller; four, 2017 vintage Surrette FC-420 flooded lead calcium batteries; E-Meter (Link-10).

The 7kW PV, 2 inverter system typically sells an average of 20 kWh/day.
Peak summer production is 50 kWh/day.

The original, April of 1999, Home Power guerilla solar system #2 was legally permitted in April of 2005, with grandfathered yearly net metering through PP&L.

I also have a 2 @ 4' X 10' flat plate, glycol based SHW system which provides 85% of our yearly hot water needs.

Our home is zero energy which includes winter heating, hot water & charging of our 2013 Chevy Volt.
Location: Mt. Shasta, CA.
Contact:

Re: What is the status of Outback Power

Post by shastatodd » Mon Mar 30, 2026 12:46 am

This is good news so hopefully my spare set of boards and spare refurbished inverter will not need using for some time.

Post Reply