Coexist? Mate3 & AXS Port on a Hub?
- eastrader
- Forum Whiz
- Posts: 39
- Joined: Mon May 27, 2019 2:09 pm
- My RE system: VFXR 3648 inverter
FM 80 charge controller
Mate 3 +
Off Grid
4 x Samsung 100ah lithium batteries
8 Polycrystalline solar panels (240-250 watt) - Contact:
Coexist? Mate3 & AXS Port on a Hub?
I have a friend who has a small problem. When moving his Mate 3 from the solar room to a better location in his off-grid home the cables got reversed..
Thus the internet port on the Mate3s is dead but the Mate3s does work still (no motherboard available to buy). However, to remote monitor his system can we add the AXS Port?
I have read the manual but it does not cover both devices on the Hub.
Suggestions, ideas? Experience?
Thus the internet port on the Mate3s is dead but the Mate3s does work still (no motherboard available to buy). However, to remote monitor his system can we add the AXS Port?
I have read the manual but it does not cover both devices on the Hub.
Suggestions, ideas? Experience?
Hybrid solar/ grid is my desire
-
raysun
- Forum Overlord
- Posts: 13665
- Joined: Tue Jul 26, 2016 5:57 am
- My RE system: (Former system. Now retired.)
Flexpower Two: (2) FXR3048A-01 - Series Stacked, (2) FM80, MATE3s, FlexNetDC
6 SimpliPhi 3.8-48 (48v @ 75AH. 450AH total)
Outback IBR3 battery enclosure
REC Alpha 440W panels - 2 arrays: each of 4 strings of 2 in series
2 Midnite Solar MNPV6 combiners w/20A DC disconnects.
Honda EU7000is gas fuel generator
Off-Grid
Re: Coexist? Mate3 & AXS Port on a Hub?
The Mate3 and the AXS Port cannot be active on the same Hub.
If not replacing the Mate3s with another, an AXS Port is a viable alternative - especially paired with Andrew Welch's WattPlot program.
If not replacing the Mate3s with another, an AXS Port is a viable alternative - especially paired with Andrew Welch's WattPlot program.
-
RoryM
- Forum Junior Member
- Posts: 2
- Joined: Sun Feb 03, 2019 12:31 pm
- My RE system: 100% offgrid system initially online July 2018. Uses Radian
Series GS8048A inverter/charger. I have 7KW solar generation
split between 2 FlexMax 80 solar charger controllers.
I am using 2 Discover Helios ESS Batteries 628 Ah total (52VDC). Primary interface is with
Mate3s (Firmware Version 1.4.7) but I also access my system
using my OpticsRE interface connection.
Re: Coexist? Mate3 & AXS Port on a Hub?
So I've got a question. I'm wanting to add the ability to monitor my system w/o using the internet. I currently have Opticsre working (and it works just fine for me). But I'm concerned about the internet going down or the Opticsre server availability. I see two options 1) adding an AXS Port. I can source the AXS Port hardware on eBay. But reading through the installation instructions the AXS Port requires Opticsre installed locally. 2) Adding WattPlot.
My 1st. problem is I can't find the Opticsre Download. Yes I looked; the Opticsre software download isn't where the installation instructions indicates...
My 2nd. problem is due to the Trump Tarriff, the Wattplot download and activation is now blocked. The programmer seems rather sincere about NOT allowing anymore USA customers...Alas. another road block...
Any idea where I can download a version of Opticsre?
thanks...rory
My 1st. problem is I can't find the Opticsre Download. Yes I looked; the Opticsre software download isn't where the installation instructions indicates...
My 2nd. problem is due to the Trump Tarriff, the Wattplot download and activation is now blocked. The programmer seems rather sincere about NOT allowing anymore USA customers...Alas. another road block...
Any idea where I can download a version of Opticsre?
thanks...rory
Re: Coexist? Mate3 & AXS Port on a Hub?
There is not a download for OpticsRE. It is a cloud based service. Could you please link or point to me where it says that there is a local interface you should download? I also would like to advise that there is little to no technical support from us for the AXS. https://outbackpower.com/downloads/docu ... manual.pdf In previous Mates, you could type the IP address from the Mate into your browser and it would pull up a local interface, but it wasn't real time info, I believe it reported in 15 minute intervals. In most cases, when OpticsRE goes down, it should back fill the data. Some times it looks like large spikes on the next day. We are able to aggregate some of the data.RoryM wrote: ↑Thu Mar 20, 2025 11:39 amSo I've got a question. I'm wanting to add the ability to monitor my system w/o using the internet. I currently have Opticsre working (and it works just fine for me). But I'm concerned about the internet going down or the Opticsre server availability. I see two options 1) adding an AXS Port. I can source the AXS Port hardware on eBay. But reading through the installation instructions the AXS Port requires Opticsre installed locally. 2) Adding WattPlot.
My 1st. problem is I can't find the Opticsre Download. Yes I looked; the Opticsre software download isn't where the installation instructions indicates...
My 2nd. problem is due to the Trump Tarriff, the Wattplot download and activation is now blocked. The programmer seems rather sincere about NOT allowing anymore USA customers...Alas. another road block...
Any idea where I can download a version of Opticsre?
thanks...rory
- Kim
Technical Support


-
provo
- Forum Emperor
- Posts: 1464
- Joined: Thu Jul 27, 2006 4:34 pm
- My RE system: 16 Evergreen EC-120 (4 strings, total 1920W)
2 SimpliPhi 3.8-m-24V (150Ah each)
One FM80
One VFXR3524A
Hub 10
Mate3s
FNDC
Honda EU3000is generator
Grid connection, no selling back - Location: Sierra foothills
Re: Coexist? Mate3 & AXS Port on a Hub?
I have a Mate3s and it does show a local interface on my browser. It's real time (and much faster than OpticsRE), but read only -- no way to modify parameters like Optics will.
- eastrader
- Forum Whiz
- Posts: 39
- Joined: Mon May 27, 2019 2:09 pm
- My RE system: VFXR 3648 inverter
FM 80 charge controller
Mate 3 +
Off Grid
4 x Samsung 100ah lithium batteries
8 Polycrystalline solar panels (240-250 watt) - Contact:
Re: Coexist? Mate3 & AXS Port on a Hub?
I think I have wattplot on a PC.. will chk when I get home.
Hybrid solar/ grid is my desire
Re: Coexist? Mate3 & AXS Port on a Hub?
Thank you, this is good to know. One of the other techs tried on their own system and couldn't get it to work. Is it the same as before where you input the IP address of the Mate to the browser?
-Kim
Technical Support


Re: Coexist? Mate3 & AXS Port on a Hub?
Technical Support


-
provo
- Forum Emperor
- Posts: 1464
- Joined: Thu Jul 27, 2006 4:34 pm
- My RE system: 16 Evergreen EC-120 (4 strings, total 1920W)
2 SimpliPhi 3.8-m-24V (150Ah each)
One FM80
One VFXR3524A
Hub 10
Mate3s
FNDC
Honda EU3000is generator
Grid connection, no selling back - Location: Sierra foothills
Re: Coexist? Mate3 & AXS Port on a Hub?
Yup -- I find that the URL gets "changed" fairly often which causes the browser to fail. Often I can get it working again by just incrementing the last two digits. If it was xxx.xxx.xxx.40, I just make it xxx.xxx.xxx.41 and I'm back in business.
- eastrader
- Forum Whiz
- Posts: 39
- Joined: Mon May 27, 2019 2:09 pm
- My RE system: VFXR 3648 inverter
FM 80 charge controller
Mate 3 +
Off Grid
4 x Samsung 100ah lithium batteries
8 Polycrystalline solar panels (240-250 watt) - Contact:
Re: Coexist? Mate3 & AXS Port on a Hub?
Software is not political, he chooses to lose money. There is another solution via Github and a raspberry pi.
Plus he is hurting people that paid for his Wattplot. I ran it and had so many problems. His response had so many cevats that made it unworkable with outback systems.
If you want and have time get a raspberry pi , set it to communicate with a mate or AXS port. And set it as a server, then you can log in and see your system.
Plus he is hurting people that paid for his Wattplot. I ran it and had so many problems. His response had so many cevats that made it unworkable with outback systems.
If you want and have time get a raspberry pi , set it to communicate with a mate or AXS port. And set it as a server, then you can log in and see your system.
Hybrid solar/ grid is my desire
-
chrisski
- Forum Czar
- Posts: 536
- Joined: Fri May 17, 2024 7:23 pm
- My RE system: Dual 8048 Radian w/ Load Center
Mate 3
Flex max 100 afci X 4
Fortress eFlex 5.1 kWh Battery X 8
TP1000 for Internet Connectivity - Location: Central AZ, lowland desert
Re: Coexist? Mate3 & AXS Port on a Hub?
What is this other solution via GitHub and Rasberry pi?eastrader wrote: ↑Thu Mar 27, 2025 3:23 pmSoftware is not political, he chooses to lose money. There is another solution via Github and a raspberry pi.
Plus he is hurting people that paid for his Wattplot. I ran it and had so many problems. His response had so many cevats that made it unworkable with outback systems.
If you want and have time get a raspberry pi , set it to communicate with a mate or AXS port. And set it as a server, then you can log in and see your system.
A link would be nice.
- eastrader
- Forum Whiz
- Posts: 39
- Joined: Mon May 27, 2019 2:09 pm
- My RE system: VFXR 3648 inverter
FM 80 charge controller
Mate 3 +
Off Grid
4 x Samsung 100ah lithium batteries
8 Polycrystalline solar panels (240-250 watt) - Contact:
Re: Coexist? Mate3 & AXS Port on a Hub?
Sorry, lost internet during post.
Try here
https://github.com/wildmountainfarms/solarthing
It may need a few updates.
Try here
https://github.com/wildmountainfarms/solarthing
It may need a few updates.
Hybrid solar/ grid is my desire
-
raysun
- Forum Overlord
- Posts: 13665
- Joined: Tue Jul 26, 2016 5:57 am
- My RE system: (Former system. Now retired.)
Flexpower Two: (2) FXR3048A-01 - Series Stacked, (2) FM80, MATE3s, FlexNetDC
6 SimpliPhi 3.8-48 (48v @ 75AH. 450AH total)
Outback IBR3 battery enclosure
REC Alpha 440W panels - 2 arrays: each of 4 strings of 2 in series
2 Midnite Solar MNPV6 combiners w/20A DC disconnects.
Honda EU7000is gas fuel generator
Off-Grid
Re: Coexist? Mate3 & AXS Port on a Hub?
There's absolutely nothing on Github that doesn't need a few updates.eastrader wrote: ↑Thu Mar 27, 2025 6:15 pmSorry, lost internet during post.
Try here
https://github.com/wildmountainfarms/solarthing
It may need a few updates.
-
Echo5
- Forum Guru
- Posts: 107
- Joined: Tue Aug 08, 2023 2:00 am
- My RE system: FLEXmax 80, VFXR 3024, MATE3s, HUB10, FLEXnet DC, 2x150Ah Sterling LiFePO4 24V batteries, 8x220w panels in 4 strings of 2.
- Contact:
Re: Coexist? Mate3 & AXS Port on a Hub?
Perhaps consider Kimono - it is free and open source. It gives you monitoring over your own LAN, however it cannot update. It is read only.
https://www.youtube.com/watch?v=WtzF9pmowZg
Kimono: Free and Open Source Outback Monitoring software
http://www.OfItselfSo.com/Kimono
http://www.OfItselfSo.com/Kimono
-
RoryM
- Forum Junior Member
- Posts: 2
- Joined: Sun Feb 03, 2019 12:31 pm
- My RE system: 100% offgrid system initially online July 2018. Uses Radian
Series GS8048A inverter/charger. I have 7KW solar generation
split between 2 FlexMax 80 solar charger controllers.
I am using 2 Discover Helios ESS Batteries 628 Ah total (52VDC). Primary interface is with
Mate3s (Firmware Version 1.4.7) but I also access my system
using my OpticsRE interface connection.
Re: Coexist? Mate3 & AXS Port on a Hub?
OK, this solution is exactly what I was hoping I would find. Just a simple way of monitoring my system remotely through my local network...Just use the IP address in a web browser. I tried both WIN11 (using duck-duck-Go) and Samsung Tablet Android (using Brave). Works great on both.
Disclaimer; Now I could has sworn I previously attempted to ping my Mate3s controller (with no reply); otherwise I would have tried opening the URL with a browser...But I didn't
That's probably enough of me telling everyone how stupid I feel right now...
Outback should probably tell someone how easy it is to open the Controller IP Address with a web browser to read the system status...By my measure the Data is being updated every 5 seconds...No control just read only...Perfect for showing my wife w/o worrying about things getting changed inadvertently... I was worried about that with showing her opening with Opticsre...
I'm also going to try (by try I mean attempt or simply check out) the Githup/Rasberry PI solution as well as Kimono...but honestly, the Local Web access using a web browser is a great solution without any draw backs. Namely; Low cost, simplicity, protected access, No need to buy any equipment, and several others incidental benefits I'm sure (like I don't have to upset anyone in Canada)...
Wow, this chat was most helpful...many Thanks. Give everyone a "two thunbs up" for sure!
regards, rory
Disclaimer; Now I could has sworn I previously attempted to ping my Mate3s controller (with no reply); otherwise I would have tried opening the URL with a browser...But I didn't
That's probably enough of me telling everyone how stupid I feel right now...
Outback should probably tell someone how easy it is to open the Controller IP Address with a web browser to read the system status...By my measure the Data is being updated every 5 seconds...No control just read only...Perfect for showing my wife w/o worrying about things getting changed inadvertently... I was worried about that with showing her opening with Opticsre...
I'm also going to try (by try I mean attempt or simply check out) the Githup/Rasberry PI solution as well as Kimono...but honestly, the Local Web access using a web browser is a great solution without any draw backs. Namely; Low cost, simplicity, protected access, No need to buy any equipment, and several others incidental benefits I'm sure (like I don't have to upset anyone in Canada)...
Wow, this chat was most helpful...many Thanks. Give everyone a "two thunbs up" for sure!
regards, rory
-
raysun
- Forum Overlord
- Posts: 13665
- Joined: Tue Jul 26, 2016 5:57 am
- My RE system: (Former system. Now retired.)
Flexpower Two: (2) FXR3048A-01 - Series Stacked, (2) FM80, MATE3s, FlexNetDC
6 SimpliPhi 3.8-48 (48v @ 75AH. 450AH total)
Outback IBR3 battery enclosure
REC Alpha 440W panels - 2 arrays: each of 4 strings of 2 in series
2 Midnite Solar MNPV6 combiners w/20A DC disconnects.
Honda EU7000is gas fuel generator
Off-Grid
Re: Coexist? Mate3 & AXS Port on a Hub?
The Mate3 web app is a remarkably capable piece of software. It can monitor everything that can connect to the Mate.
I use it to monitor a pair of FXR3048A-01 inverters. FXRs, Mate3s,Hub is all that's needed.